Today I cut out the baffle seals and clecoed them in place. The seals come in a roll of rubber material, with the shapes pre-punched. It took a little time to cut out each shape with a razor, but it was easy to do. Each part is stamped with a label, and they are installed from part A to M.
The baffle seals press against the top cowling forming a seal, and forcing the airflow down through the cooling fins and into the ducting that cools engine components. Any gaps in the baffle seals means inefficient cooling and higher engine operating temperatures.
Based on some vans Air Force threads, I was ready for some of these seals to need to be switched, or flipped, or something. What I found was that if installed with the labels facing outside, everything fit just right. Except for part A, which appeared to be reversed. After a bit of deliberation, I decided it fit best with the label facing inwards. Once I have the cowling on, I guess I’ll find out!
Tonight I shaped the left hand air ramp. This was trickier than the right hand side because the ramp is part of the air filter cover. Bending the ramp risks damaging or bending the cover. I practiced on a piece of scrap, and when that came out almost perfect I got started with the real piece. The first bend went well, and the second was going well also. However when I moved to the third bend line I noticed that the cover had developed an unwanted bend and a twist. I carefully worked the unwanted bend out, and carried on with the process.
The end result was acceptable, but not my finest work. I removed the paper template, match drilled the one screw hole, deburred, dimpled, and installed a nut plate.
With the part complete, I installed the air filter and cover, and verified everything fits correctly. Then I took it all apart again, as I’ll need to replace the oil return line.
Tonight I had only a few minutes, so I riveted the right air ramp into position and glued on the template for the left air ramp. I used a pop rivet in the aft-most, inboard hole, because access by squeezer was tight, and I didn’t want to use my rivet gun for fear of bending something.
This required sticking on a paper template, then, following a sequence of bends, shaping the piece until it conforms to relatively smooth curve. It’s a conical shape, so one end is a much tighter radius than the other. I managed to get the shape fairly close, but I ended up cracking the end with the most narrow radius. I stop drilled the crack, then filed out a relief notch to mitigate the risk of further cracks.
I then match drilled the holes into the baffling, and dimpled them. Dimpling the aft most holes was a little annoying because it was too far from the edge to use my squeezer. I used a pop-rivet dimpled instead, which doesn’t give great results, but good enough in this case.
This week I chipped away at the baffle tension rods over a series of evenings. I didn’t actually have a die for cutting the threads, so I had to order one from Aircraft Spruce. These were fairly easy to make, and came out looking good. Some more practice with cutting threads might have helped, but I got the hang of it pretty quickly. When bending the rods I used a block of wood with a slot cut in it to stop the rod rotating, which allowed me to bend both ends of the rods in the same axis.
Installing the rods was fairly easy. I cut a few lengths of 1/4 inch tubing to help prevent chaffing, although there weren’t many areas where interference is possible. Once I had the tubing slid over the rods and positioned correctly, I used some RTV to bond the tubing onto the rod.
With new crush washers in hand I also took time to install the remaining baffle hardware, and torqued everything.
Today I spent time adjusting the front baffles to fit nicely against the engine case. The front left baffle took the most adjusting, and after several iterations I was happy with the fit.
With the baffles fitting nicely I went ahead and installed the hardware and torqued everything up. I have run out of -40 star washers, so I ordered some more and put tape on the screws that were missing washers.
Tonight I test fit the front baffles. The front right baffle was the easiest to install, and looks to be a good fit. The front left was more challenging, but after disconnecting the oil return line, I was able to get it into position. This one will need a little adjustment to properly conform to the engine casing, and a couple of corners that need some easing.
In the process of test fitting the front baffles I noticed that I had made an error with the front center bracket. Just like the aft bracket, I had misread the drawing and had it on the left side instead of the right side of the centerline. Then I noticed I had the bolt installed from left to right, instead of right to left, on both brackets. It’s probably not a big deal, but it always makes me nervous when I miss something or find an error. What else did I miss?
I fixed the errors with the bracket, installed the hardware and torqued the nuts.
Over the last few evenings I’ve made a little progress on the front baffling.
I riveted together the parts, and applied RTV where instructed. The RTV strips are to reduce chaffing on the engine cylinder cooling fins. RTV is also used to help glue the mesh in place covering the cabin hot air intake.
These are ready to be test-fit onto the engine and trimmed (if necessary).
Tonight I worked on the front baffles, including the air ramp. Dad had already made progress drilling and deburring parts, and installing nut plates. I picked up where he left off and completed a page of steps.